Lawn Repair System – Lawn Cutter & Lawn Cultivation
inkl. MwSt.
GRATIS Versand ab Mindestbestellwert
In stock
Beschreibung
Kompatibilität
Technische Daten
Lieferumfang
Scope of delivery (depending on selected variant)
Starter set
- 1x handle (depending on selection: hoop or ball)
- 1x handle shaft (depending on the desired working height selected: 116 cm or 104 cm)
- 1x ejector
- 1x base plate with cutting line
- 1x growing box
- 1x insert tray
- 1x compactor
- 4x stacking system columns
- 1x saucer
Starter set XXL
- 1x handle (depending on selection: hoop or ball)
- 1x handle shaft (depending on the desired working height selected: 116 cm or 104 cm)
- 1x ejector
- 1x base plate with cutting line
- 3x growing box
- 3x insert tray
- 1x compactor
- 12x stacking system columns
- 1x saucer
Note: The exact scope of delivery depends on the selected product variant.All other items shown are for illustration purposes only and are not included in the scope of delivery.
Montage
Assembly Recommendation - Lawn Edger
Our assembly recommendations are intended as non-binding guidance.
Some recommendations are shown as examples - the color and shape of the parts may differ. However, the general instructions still remain valid.
Required tools, aids and protective equipment:
- No additional tools required
- Optional: medium-strength threadlocker
Assembly process:
- Carefully position the handle on the threaded sleeve of the base plate and screw it in clockwise by hand until it is fully tightened against the stop.
Tip: for additional hold, a medium-strength threadlocker can be used on the threads. This only allows limited quick disassembly - use as needed. - Place the handle on the thread of the handle and screw it on clockwise by hand.Thread must not be overtightened.
Tip: For the bail handle, a horizontal alignment with the logo orientation on the ejector is recommended to ensure ergonomic handling. - Ejector from above in the matching position to the recesses and insert
Assembly recommendation - lawn cultivation system
Our assembly recommendations serve as non-binding guidance.
Some recommendations are illustrative - the color and shape of the parts may vary. The basic instructions remain valid nonetheless.
Required tools, aids, and protective equipment:
- No additional tools required
Assembly process:
- Positioning the columns: Position the columns of the stacking system at the four end markings of the lawn cultivation box.
- Top assembly: Hook the column onto the designated mark at the top.
- Bottom assembly: Press the lower section of the column against the box until it sits flush. Repeat the process for all four columns.
Note: first hook at the top, then press in at the bottom - not the other way around. - Setup: Place the box with the mounted columns onto the base. Make sure that the tabs and holes are aligned. Press down lightly from above.
- Stacking: Place additional boxes with mounted columns on top and stack as desired. Ensure a stable and level position.
Anwendung
Application - Lawn Edger
Our assembly recommendations serve as a non-binding guide.
Some recommendations are examples – the color and shape of the parts may vary. However, the basic instructions remain valid.
Required tools, aids and protective equipment:
- Turf regeneration box with pre-grown turf element
- Water (for dry or compacted soil)
- Sturdy footwear
Note:
- For dry or hard soil, the repair area should be watered in advance
- Always guide the tool perpendicular to the surface to ensure clean cut edges
- Do not force penetration - do not assist with hammer blows
- Remove the ejector before cutting out, as it may be damaged when stepped on
- Cutting out and ejecting take place in separate work steps
- If residual moisture remains in the threaded area, it is recommended to unscrew the handle for storage to ensure complete drying and prevent superficial red rust.
Process:
- Damage area: Define the damaged area to be replaced.
- Watering: If the soil is dry or hard, lightly water the area beforehand.
- Positioning: Place the turf cutter centrally on the damaged area.
- Ejector: Be sure to remove the ejector beforehand (see note)
- Piercing: Gradually apply your body weight to the turf cutter so that it cuts into the soil.
Tip: The cutting action can be supported by gentle rocking movements. - Pressing in: Press the tool into the ground as far as the base plate.
- Releasing: Pull the cutter slowly upward with a gentle rocking motion.
- Insert ejector: Insert the ejector into the intended recesses in the base plate.
- Removal: With light pressure on the ejector, release the damaged area downward from the cutter while guiding the tool upward.
- Select replacement: Select a pre-cut turf element.
- Removal: Remove the turf element completely from the turf growing box by pressing upward from below against the insert base.
- Insertion: Insert the turf element into the prepared opening.
- Leveling: Gently press down the transition to the existing area with your foot.
- Aftercare: Water the area lightly to support the establishment phase.
Application - Turf growing system
Our application recommendations are intended as non-binding guidance.
Some recommendations are examples only - the color and shape of the parts may vary. The basic instructions remain valid nonetheless.
Required tools, aids, and protective equipment:
- Lawn substrate / soil-sand mixture with any mixing ratio, preferably as similar as possible to the existing soil.
Example: topsoil + quartz sand with a grain size of 0.8 - 1.6 mm in a 70 / 30 ratio - Seed analogous to the existing lawn
- Water
Note:
- Markers for filling and compaction serve as a guide
- The actual compaction depends on the substrate and moisture level
Procedure:
- Insert insert base: Insert the insert base into the lawn growing box.
- Fill in substrate: Fill the first layer of lawn substrate evenly into the box up to the top edge of the first marking.
- Pre-compacting#1: Compact the substrate with the compactor up to the lower edge of the first marking.
- Filling: Fill in another layer of substrate up to the upper edge of the second marking.
- Pre-compacting#2: Compact the substrate with the compactor up to the lower edge of the second marking.
- Applying seed: Distribute the lawn seed evenly over the prepared surface with the desired application rate, if possible analogously to the existing lawn.
- Covering: Fill in substrate up to the upper edge of the lawn growing box to cover the seed.
- Stripping: Remove excess substrate evenly.
- Final compaction: Lightly press down the surface to ensure good soil contact for the lawn seeds.
- Watering: Initially moisten the substrate evenly and not too heavily until water drains out at the bottom..
- Positioning the columns: Position the columns of the stacking system at the four front markings of the lawn growing box. Hook the column onto the designated marking at the top.
- Bottom installation: Press the lower part of the column until it lies flat against the box. Repeat the process for all four columns.
Note: hook at the top first, then press at the bottom - not the other way around. - Setup: Place the box with the mounted columns on the saucer. Make sure the lugs and drill holes are aligned.
- Joining: Press down gently from above.
- Stacking: Place additional boxes with mounted columns on top and stack as desired. Ensure a stable and level position.
Hinweise & Gewährleistung
Das sagen unsere Kunden
Rezensionen von echten Rasenprofis
KEINE AUSGEFRANSTEN HALME MEHR – DER SCHNITT IST EINFACH VITALER UND SAUBERER
PASST PERFEKT. SUPER VERARBEITUNG. SCHNITTERGEBNIS 1A. FAST GERÄUSCHLOS.
FAQ - häufig gestellte Fragen
- Führt der 3D-Druck zu einer unregelmäßigen Oberfläche?
Die Qualität und Optik der Oberflächenstruktur ist ein wesentlicher Bestandteil unserer Produktgestaltung.
Schichthöhe:
Unsere Schichthöhen sind optimal gewählt, um eine perfekte Balance zwischen optischer Qualität und mechanischer Festigkeit zu gewährleisten.
Hochauflösende Drucktechnologien:
Dank fortschrittlicher Druckverfahren entstehen präzise Details und eine gleichmäßige Oberflächenstruktur.
Qualitätsgarantie:
Unsere zoomfähigen Produktbilder ermöglichen dir eine detaillierte Ansicht der Druckoptik und verdeutlichen die hochwertige Verarbeitung.
- Hält das Material der Belastung stand?
Unsere Produkte wurden sorgfältig entwickelt, um auch unter erhöhter Belastung langlebig und sicher zu bleiben.
Hochfestes Material:
Wir verwenden UV- und witterungsbeständige thermoplastische Kunststoffe, die besonders robust und langlebig sind.
Festigkeitsoptimiertes Design:
Die Konstruktion ist speziell darauf ausgelegt, mechanischen Belastungen standzuhalten und eine zuverlässige Leistung zu gewährleisten.
Umfangreiche Tests:
Im Gegensatz zu vielen anderen Herstellern durchlaufen unsere Messerteller Praxislangzeiterprobungen, eine Fliehkraftprüfung zur Festigkeitsbestimmung sowie eine Unwuchtprüfung – während die Systeme anderer oft ungetestet bleiben.
