• 1x sheet set on backing material

Delivered rolled up 

Note: Design according to selection. All other items shown are for illustration purposes only and are not included in the scope of delivery.

Installation recommendation – design wrapping

Our installation recommendation serves as a non-binding guide.
Some recommendations are exemplary – the color and shape of the parts may vary. However, the basic instructions remain valid.

General information

• The printing is produced in high resolution with color-accurate reproduction and high detail accuracy.Color deviations between the digital representation and the actual product may occur due to material and display-related factors
• Our films, including the protective laminate optimally matched to them, are based on high-quality wrapping materials and have been specially developed for complex 3D plastic surfaces as well as substrates with low surface energy
•  They offer high formability, controllable stretch, and excellent recovery properties (memory effect) for safe and reproducible application
• The design of the film contours is intended to ensure processing that is as simple, user-friendly, and safe as possible
• Our film sets have been tested multiple times under real conditions and applied successfully and reproducibly – even under practical user conditions
• In individual cases, local stresses may occur depending on the geometry and processing.If these cannot be fully removed, parts of the film in these areas can be carefully adjusted or trimmed to achieve an optimal result
• Benefit of protective laminate:
  • UV resistance 
  • Scratch resistance 
  • Durability

• Up to 7 years of outdoor durability
• Thanks to air-channel technology, air bubbles can simply be smoothed out (no needle required)
• The films are not suitable for wet application
• All contours are pre-designed to fit precisely and are intended for user-friendly application
• Safety distances to component edges and adjacent film sections are structurally accounted for (~3 mm)
• The material thickness is chosen for optimally easy handling
• Ideally, installation should be carried out by two people, especially with larger film pieces
• Apply large sections in stages
• Work calmly and without time pressure
• When applying the film, we recommend wearing dry fabric gloves
• The film has a repositionable adhesive for easier placement during application
• If in doubt, it is better to start again rather than force it, especially if:
  • wrinkles cannot be worked out cleanly
  • the film is visibly under tension
  • the position deviates significantly
  • larger bubbles form that cannot be spread out 

In these cases:

• • Carefully peel the film off again and, if necessary,slightly warm. The film returns to its original state.
  • Allow to cool and reposition
  • Reapply cleanly

• Handling heat

• Only warm the film slightly, do not overheat 
• Guideline: lukewarm (~50 °C) 
• Keep the hot air gun moving at all times to avoid excessively high local temperatures (hot spots)
• Distance approx. 20–30 cm

• Required tools
  • Felt squeegee
  • Utility knife
  • Heat gun, optional hair dryer

 1. Requirements / environment

• Processing temperature: ideal 18–25 °C (minimum ≥15 °C) 
• Clean, dry, dust-free environment
• No direct sunlight during application 

2.Preparing the surface

• Thoroughly clean and degrease the surface (e.g., with isopropanol or suitable plastic cleaners)
• If using other cleaning agents, first check their compatibility with the plastic on an inconspicuous area
•  Then wipe the surface dry with a lint-free cloth and allow it to dry completely.

 3. Positioning

• Pre-position film parts dry and check the position
• Memorize the position / set reference points 

4.Adhesion

• Dry application expressly recommended
• High initial adhesion already achieved after 20 minutes
• Work from the center outward
• On smooth surfaces, smooth out with a felt squeegee and even pressure
• On curved surfaces, smooth out with a finger
• Smooth out air bubbles
• Apply large film sections in stages 
• Film can be carefully lifted and repositioned if necessary 

5.Processing on strongly curved surfaces

• For curves and edges: 

• Warm the film slightly and apply
• The material becomes stretchable and conforms to the shape and can be slightly formed be

• Do not overstretch; avoid tension as much as possible 
• In case of greater deformation: 

• Allow the film to relax briefly (memory effect)

 6. Adhesive activation (post-heating)

• Full-surface, light and gradual reheating to activate the adhesive, especially in the following areas:

• Edges
• Depressions
• areas with heavy deformation

7.Critical areas

• Press edges and transitions down particularly carefully 
• Do not apply excessive heat, otherwise there is a risk of damage to the plastic surface
• Warm particularly carefully in the camera and display areas
• Rework transitions several times if necessary

8. Curing

• Do not use the mower for 24–48 hours
• Temperature >20 °C recommended
• Maximum final adhesion is achieved after 24 hours

9. Removing the film after appropriate use

• Gently warm the film
• Gradually peel off the film at an angle of 60° to 90° between the film and the surface
• Any adhesive residue can be easily removed with an adhesive remover (e.g. with isopropanol)  and a cotton cloth (test compatibility with the surface beforehand)

10.Sample videos

A) Installation recommendation based on a Mammoton Luba mini 2 AWD

B) Installation recommendation based on a Ecovacs Goat A1600

C) Installation recommendation based on a Anthbot Genie

🔵 Moderat

Dieses Design besitzt einen mittleren Verarbeitungsaufwand.

Für optimale Ergebnisse empfehlen wir eine sorgfältige Ausrichtung sowie etwas Geduld bei komplexeren Konturen und 3D-Oberflächen.

Die Einstufung basiert auf unserer eigenen Erfahrung und wurde aus Sicht eines durchschnittlichen Anwenders vorgenommen. Sie dient als unverbindliche Orientierungshilfe zum Verarbeitungsaufwand.