• 1x sheet set on backing material

Delivered rolled up 

Note: Design according to selection. All other items shown are for illustration purposes only and are not included in the scope of delivery.

Assembly recommendation – design film

Our assembly recommendation serves as non-binding guidance.
Some recommendations are exemplary – the color and shape of the parts may vary. However, the basic instructions remain valid.

General information

• The print is produced in high resolution with accurate color reproduction and high detail accuracy.Color variations between the digital representation and the actual product may occur due to material and display-related factors
• Our films, including the protective laminate optimally matched to them, are based on high-quality wrapping materials and are specially developed for complex 3D plastic surfaces as well as substrates with low surface energy
•  They offer high formability, controlled stretch, and excellent recovery properties (memory effect) for safe and reproducible application
• The design of the film contours is intended to ensure processing that is as simple, user-friendly, and safe as possible
• Our film sets have been tested multiple times under real conditions and successfully and reproducibly applied – even under practical user conditions
• In individual cases, local stresses may occur depending on the geometry and processing. Should these not come off completely, film sections in these areas can be carefully adjusted or trimmed to achieve an optimal result
• Advantage of protective laminate:
  • UV resistance 
  • Scratch resistance 
  • Durability

• Up to 7 years of outdoor durability
• Thanks to air-channel technology, air bubbles can be easily smoothed out (no needle required)
• The films are not suitable for wet application
• All contours are precisely pre-designed and intended for user-friendly application
• Safety distances to component edges and adjacent film sections are taken into account by design (~3 mm)
• Material thickness is selected for optimally easy handling
• Installation should ideally be carried out by two people, especially for larger film pieces
• Apply large pieces in stages
• Work calmly and without time pressure
• When applying the film, we recommend wearing dry fabric gloves
• The film has a repositionable adhesive for easier placement during application
• If in doubt, it is better to start again than force it, especially if:
  • wrinkles cannot be worked out cleanly
  • the film is visibly under tension
  • the position deviates significantly
  • larger bubbles form that cannot be smoothed out 

In these cases:

• • Carefully peel the film off again and if necessaryslightly warm it. The film returns to its original state.
  • Allow to cool and reposition
  • Reapply cleanly

• Handling heat

• Heat the film only slightly, do not overheat 
• Guideline: lukewarm (~50 °C) 
• Keep the hot air gun moving at all times to avoid excessively high local temperatures (hot spots)
• Distance approx. 20–30 cm

• Required tools
  • Felt squeegee
  • Utility knife
  • Hot air gun, optionally hair dryer

 1. Requirements / environment

• Processing temperature: ideal 18–25 °C (minimum ≥15 °C) 
• Clean, dry, dust-free environment
• No direct sunlight during application 

2.Surface preparation

• Clean and degrease the surface thoroughly (e.g. with isopropanol or suitable plastic cleaners)
• If using other cleaning agents, first test their compatibility with the plastic in an inconspicuous area
•  Then wipe the surface dry with a lint-free cloth and allow it to dry completely.

 3. Positioning

• Pre-position the film parts dry and check the position
• Memorize the position / set reference points 

4.Adhesion

• Dry application expressly recommended
• High initial tack achieved after just 20 minutes
• Work from the center outward
• On smooth surfaces, smooth out with a felt squeegee using even pressure
• On curved surfaces, smooth out with your finger
• Smooth out air bubbles
• Apply large film sections in stages 
• Film can be carefully lifted and repositioned if needed 

5.Processing on strongly curved surfaces

• For curves and edges: 

• Gently warm the film and apply it
• The material becomes stretchable and adapts and can be slightly shaped be

• Do not overstretch; avoid tension as much as possible 
• For more pronounced deformation: 

• Allow the film to relax briefly (memory effect)

 6. Adhesive activation (post-heating)

• Light, gradual post-heating over the entire surface to activate the adhesive, especially in the following areas: 

• Edges 
• Depressions
• heavily deformed areas

7.Critical areas

• Press edges and transitions down particularly carefully 
• Do not apply too much heat, otherwise damage to the plastic surface may occur
• Warm carefully in areas around the camera and display
• Touch up transitions several times if necessary

8. Curing

• Do not use mower for 24–48 hours
• Temperature >20 °C recommended
• Maximum final adhesion achieved after 24 hours

9. Removing the film after appropriate use

• Gently warm the film
• Gradually peel off the film at an angle of 60° to 90° between the film and the surface
• Any adhesive residue can be easily removed with an adhesive remover (e.g. with isopropanol) and a cotton cloth (test compatibility with the surface beforehand)

10.Sample videos

A) Installation recommendation based on a Mammoton Luba mini 2 AWD

B) Installation recommendation based on a Ecovacs Goat A1600

C) Installation recommendation based on a Anthbot Genie

🟣 Anspruchsvoller

Dieses Design besitzt einen höheren Verarbeitungsaufwand.

Komplexe Geometrien, starke Rundungen und präzise Übergänge erfordern eine sorgfältige Verarbeitung.

Die Einstufung basiert auf unserer eigenen Erfahrung und wurde aus Sicht eines durchschnittlichen Anwenders vorgenommen. Sie dient als unverbindliche Orientierungshilfe zum Verarbeitungsaufwand.